Fitting A Cat Flap

It might seem daunting to install the flap for your cat however, with the proper instructions it's not that hard. Find out how high you'd like the flap to be (normally, it is at belly height). Then, mark this area on the door and then use the template as a guide to drill.

If you have a small kitten you can prop the door open very slightly and gradually allow it to go through. Reward it when it goes through.

Take a measurement of the door

A cat flap allows your pet to go in and out of your home at any time. This can keep your cat in good health as it will ensure it is getting enough exercise and will also allow it to go back inside if it gets trapped outside during bad weather. It can also reduce the amount of time you have to spend letting it out or in. It can keep your home safe by allowing you to be aware of when it went out.

It is crucial to make sure that the cat flap is installed correctly to stop your pet from being pushed through through it by other animals (e.g. dogs). It is essential to measure the height of your pet's belly as well as the doorway of your house to ensure that the flap is at the correct height. If your cat flap fitting near me is a little longer or taller than the normal, you can adjust the flap's position by moving it up or down by a tiny amount.

Then, use a spirit-level to mark the center of the door. This is where you'll install the flap. Then, using the marks as an outline, cut the shape of your flap using the aid of a Jigsaw. After you've cut the area out then sand the edges to create smooth surfaces. Drill any necessary holes.

Fitting a cat flap should not take longer than two hours. The process is a bit more complicated if you are required to put it in the form of a upvc door panel with cat flap door or a composite one. This is due to the fact that these doors are available in a variety of thicknesses, which can affect the way holes are cut. We always suggest to contact a professional if this is your first time working with glass.

Measure Your Cat

You will not have to spend hours of ignoring the pet meow to be allowed in or out. This is particularly useful when you're at work most of the day and your cat has to stay inside waiting until you get home in any weather.

It is essential to measure your cat first before you begin the installation. Although it might seem like a simple operation it is essential to get the measurement right or your cat will find it difficult to use.

First, make sure that your cat is calm prior to taking measurements. You will need to hold them in a way that they cannot move and make sure that the measuring tape or ruler is flat against their body and not bending in any place. You can take a precise measurement by keeping the measuring tape or ruler flat against the body of the animal from the top to the bottom.

Once you've got your cat's measurements, it's time to examine the door to determine where to put the flap. The flap should be placed at the level of your cat's belly. This will allow them to go through the door with minimal effort. This will also stop the flap from making a lot of noise as it moves back and back.

You will need to think about the thickness of the uPVC or composite door as well. While timber doors are of a similar thickness, uPVC and composite doors can be very different in their overall construction and can make fitting a cat flap more complicated as you will need to make sure the hole you cut is the right size for your pet.

You can also use the template included in the instructions to mark the location of the opening on the door. This will allow you to determine where the hole must be placed and ensure that the template is placed properly on the door. It is also a good idea to utilize a spirit-level to make sure that the template is placed perfectly against the door.

Cut the Flap

You will need to cut an opening in the door panel for your cat flap fitting flap prior to you can put it in place. It's a challenging job so it's recommended you hire a professional to assist you if you don't have the expertise or experience. It is also recommended to consult the instructions that come with the kit to find out how to do this correctly.

To do this you need to measure the height of your cat's or kitten's belly and use this as an indicator point. As a general rule you should place the flap about 10-15 centimeters above the ground. This is the average height of the stomach for cats. Your cat will be able to go through the flap with ease and it will also give other cats or snooping neighbours an issue when trying to leave or enter.

Mark the position of the cat flap on the door using pencil. If your kit comes with the template you can place it on the door. Utilize the markings on the template to drill holes at each corner. Then, you should be able to cut out the template's shape and replace it with your cat flap.

You can put in your cat flap yourself inside an replacement upvc door panels with cat flap or wood door if you are confident using the use of a Jigsaw. Be cautious not to cut through the vertical rails or mullions of your door. You can use a Jigsaw to cut your panel into a circle or square according to the way you'd like it. Be patient and don't try to try to force the jigsaw to cut faster.

Once the hole is cut and the flap is firmly positioned, carefully place the flap onto its new home and make sure that it is securely secured. If it has caps for screws, then put these onto the protruding screws. Once the screws are in place, you can sand any rough edges of the cut and then apply sealant around any gaps to ensure that there are no draughts coming into your home.

Place the Flap

If you have a basic cat flap, you can open it and encourage your pet to go through by putting a little bit of cat food on the outside of the door. You can also push the cat using the help of a stick or your hands. Once your pet has become comfortable walking through the flap, it will be in a position to move as it pleases. This lets you let it in and out as it's wanted.

It is possible to put an animal flap into the UPVC doors or glass door, however it might not be as easy as installing one inside a wooden exterior door. This is because UPVC doors and some types of glass doors do not have an even thickness. This can affect how you cut the hole for the flap, and can also affect whether your flap fits correctly once it's been put in place.

The mounting kit may contain a template that outlines the best places to drill holes. If the kit doesn't come with an example you can use a photocopier to create your own. It's important not to press the jigsaw too in order to cut, so it doesn't leave a bigger than needed hole in your door.

Most cat flaps - visit the next page - are rectangular or square in shape but there are also some which are circular, and they are usually more difficult to install. If you have a round flap, make sure the hole is in the right place on your door. Otherwise, the cat flap installation cost might not be able to use it, and may be locked outside for the entire day (or night).

Certain models of cat flaps come with locks that let you control when your cat comes and goes. These can be very useful if you're worried about your cat going out at night and coming back in because of the darkness, or you're at work all day. Certain locks can be used for either entrance or exit, while others can be locked in both directions. This is useful for sick or elderly cats who aren't keen to go outside in bad weather.