Fitting A Cat Flap

Fitting a cat flap can appear daunting, but it is fairly simple by following the correct instructions. Decide how high you'd like your cat flap to be (normally, it is at the belly height). Then, mark this area on the door, and use the template as a reference to drill.

If you have a young kitten you can prop the door open very slightly and gradually push it to go through. Reward the kitten each time it goes through.

Measure the Door

A cat flap allows your pet to move into and out of your home at the time that is convenient for you. This can help keep your cat in good health as it ensures that it is getting enough exercise and be able to go back inside when it is stranded outside during bad weather. It can also reduce the amount of time you have to spend letting it out or in and can ensure your home is secure by allowing you to be aware of when it went out.

It is important to make sure that the cat flap is set up properly to stop your pet from being pushed through through it by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly as well as the entrance to your home in order to make sure that the flap is at the correct height. If your cat is a little taller or shorter than normal, you can adjust the flap's height by moving it up or down a small amount.

The next step is to use a spirit level to mark the center of the door. This is where you'll install the flap. Using the marking as a guide, take the jigsaw and cut the form of the flap within the door. After you have cut the flap, sand down the edges to create smooth surfaces. Drill any necessary holes.

The installation of a cat flap installer flap should not take more than two hours. However, the process can be a bit more difficult when you have to install it into a uPVC or composite door as these doors have various thicknesses that can affect the way the holes are cut and the type of door they are inserted into. This is why we always recommend calling a professional to complete the work, particularly in the event that you've never worked with glass before.

Measure Your Cat

You will not have to spend hours of ignoring the cat's meows to be let in or out. This is especially helpful for cats that are in the house during all seasons while you work.

It is important to measure your cat's measurements first before you attempt the installation. It may appear to be a simple task, but it is crucial to make sure you measure the right measurements. Otherwise, your pet may have difficulty putting it in use.

First, ensure that your cat is calm and not anxious prior to taking the measurements. You'll need to keep your cat in a place that they are unable to move. Also, make sure that the measuring tape is straight and not bent against the body. Holding the ruler or measuring tape against their body from the top of their head to the tip of their tail will enable you to make an exact measurement.

Once you have the measurement of your cat's body, it's time to take a look at the door and decide on where to put the flap. The best option is to position the flap in the middle of your cat's stomach as this will allow them to move through it with minimal effort. This will also stop the flap from making a lot of noise as it swings back and back.

You will need to take into consideration the thickness of the uPVC or composite door, as well. While timber doors are of a similar thickness, uPVC and composite doors can be very different in their overall structure, which can make fitting a cat flap more complicated because you must ensure that the hole you make is the proper size for your pet.

You can also use the template included in the instructions to mark the location of the hole in the door. This will help you determine where the hole needs to be placed and ensure that the template is set properly on the door. Using a spirit level to make sure that the template is right against the door will be very helpful.

Cut the Flap

Before you can put in your cat flap, you'll need to cut the door panel in order to create a space large enough for it. This can be a tricky job, and it is recommended that you seek the help of a professional cat flap fitter for this step in case you don't have the knowledge or skills to tackle it yourself. You can also consult the instructions provided with the kit to discover how to do it properly.

You can consider the height of your cat's or kitten's stomach as a reference. As a general rule, place the cat flap about 10-15 centimeters above the ground. This is the average height of the cat's belly. This will let your cat pass through the flap easily and will make it difficult for other cats or nosy neighbours to enter or exit.

Mark the position of the cat flap in upvc door cost flap on the door using a pencil. Next, if your kit has a paper template, lay it over the door and use the marks to drill holes in each corner of the template. Then, you should be able cut out the template's shape and replace it with your cat flap.

You can put in your cat flap yourself on the door made of wood or uPVC when you're confident with the jigsaw. Be cautious not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw to cut the panel into a circle or square according to the design of your cat flap. Be patient and don't try to try to force the jigsaw to cut faster.

Once the hole is made, carefully place the cat flap into its new place of residence. Make sure it is firmly secured. If the flap is fitted with screw caps then push them into the protruding bolts. Once the screws have been installed then sand the rough edges and seal any gaps. This will stop drafts from entering your home.

Install the Flap

If you have an ordinary cat flap insulation flap, you can try to encourage your pet to go through it by placing a small amount of cat food on the top of the door. Alternately, you can push the cat through with your hands or a stick. Once your cat is accustomed to walking through the flap, it will be in a position to move as it pleases. This will allow you to let it in and out whenever it's wanted.

It is possible to install an animal flap into the UPVC doors or glass door, but it's not as simple as putting one in a wooden external door. This is because the UPVC doors and certain types of glass doors don't have an even thickness. This could have a dramatic effect on how you cut the opening for the flap and fitting a cat flap will also affect whether the flap is fitted correctly after it has been put in place.

The mounting kit might contain a template that outlines the best places to drill holes. If the kit doesn't come with the template you can use a photocopier to make your own. When cutting, it is important to not push the jigsaw hard so that you don't make a larger hole than is necessary in your door.

Some cat flaps are available in circular shapes, which are more difficult to put in. If you have a circular flap, ensure that the hole is located in the right place on the door. Otherwise, the cat might not be able to use it, and might be locked outside for the entire day (or night).

Certain models of cat flaps have locks that allow you to control the time your cat comes and goes. They can be extremely useful if you're worried about your cat going out at night and coming back in the darkness, or if you're working all day. Some locks can be used to lock entrance or exit, while others can be locked both ways. This is useful for fitting a cat Flap older cats or sick cats who do not want to venture out in cold weather.