Fitting A Cat Flap

The process of installing a cat flap may appear daunting but it's simple to install with the proper instructions. Decide how much to install a cat flap high you'd like the flap to be (normally, it is at belly height). Note this on the door and use the template as a guideline to drill.

If you have a kitten that is still a baby then gently prop the door slightly open and invite it to pass through. Reward it when it goes through.

Take a measurement of the door

A cat flap is a wonderful method to allow your pet to come and go in and out of your house as it pleases. This will keep your cat healthy since it will ensure that it is getting enough exercise and also be able to return inside if it gets trapped outside during bad weather. It also can reduce the amount of time you have to spend letting it out or in. It will also help ensure your home is secure by allowing you to be aware of when it went out.

It is important to ensure that the cat flap is placed correctly to stop your pet from being pushed through through wall cat flap it by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly and the entrance to your home so that you can make sure that the flap is at the correct height. If your cat is larger or shorter than the average, you can alter the flap's height by moving it upwards or downwards by a small amount.

Next, use a spirit-level to mark the middle of the door. This is where you'll install the flap. Then, using the markings as an indication, cut out the contour of your flap using a Jigsaw. After cutting the area out then sand the edges to create smooth surfaces. Drill any holes you need to.

The process of installing a cat flap is not as complicated as you think, and it shouldn't take more than two hours to finish the entire task from start to the end. However, the process could be a bit more difficult in the event that you have to put it onto the door of a uPVC or composite door since these doors have an array of thicknesses that can affect the way the holes are cut and what they are inserted into. This is why we always recommend hiring a professional to complete the job, particularly when you've never dealt with glass before.

Measure Your Cat

You will not have to spend hours of ignoring the pet's meow to be allowed in or out. This is particularly helpful for cats that are inside in all weathers when you are at work.

It is crucial to measure your cat's measurements first before you attempt the installation. It might appear to be a simple task, but it's crucial to get the measurements right. In the event that you don't, your cat may find it difficult to use.

First, make sure your cat is calm before you begin taking measurements. You will need to hold them in a manner that they are not able to move, and make sure that the measuring tape or ruler is flat against their body, not bending in any place. By keeping the ruler or measuring tape against their body from the top of their head to the tip of their tail will enable you to get an precise measurement.

Once you've determined your cat's measurements and measurements, you need to examine the door to determine where to put the flap. A good tip is to place the flap in the middle of your cat's belly as this will allow them to pass through it without much effort. This will also prevent the flap from making a lot of noise as it swings open and closed.

It is also important to consider the thickness and structure of the uPVC door or composite. Although timber doors are of a similar thickness, uPVC and composite doors can be very different in their overall construction, which can make fitting cat flap in upvc door panel the cat flap more difficult since you have to ensure that the hole you cut is the correct size for your pet.

It is also worth looking through the instructions that come with the kit to locate an outline of the template that can be used to mark out the location of the hole inside the door. This will enable you to determine where the hole needs to be located and make sure that the template is positioned precisely on the door. It is also beneficial to use a spirit-level to ensure that the template is in a straight line against the door.

Cut the Flap

Before you can put in your cat flap you have to cut the door panel in order to make it large enough for it. This can be a challenging job, and it is recommended that you seek the help of a professional cat flap fitting service for this step should you not have the knowledge or skills to complete the task yourself. It is also recommended to consult the instructions that come with the kit to find out how much to install a cat flap to do it correctly.

You can take the height of the cat's or kitten's stomach as a reference. In general, place the cat flap approximately 10-15 centimeters above the ground. This is the average height of the cat's belly. This will allow your cat to pass through wall cat flap the flap with ease and will make it difficult for other cats or naughty neighbors to get in or out.

Mark the position of the cat flap on the door with a pencil. If your kit includes an outline of paper, place this over the door and use the markings to drill holes into every corner of the template. Then, you should be able to cut out the template and replace it with the cat flap.

You can install your cat flap yourself on an uPVC or wood door If you're comfortable using the use of a Jigsaw. Be careful not to cut through the mullions or rails that run vertically of your door. You can use a jigsaw to cut your panel into a square or circle according to the way you'd like to cut it. Make sure to take your time and don't try to make the jigsaw cut faster.

After the hole has been cut, carefully place your cat flap in its new home. Make sure it's solidly secured. If it features screw caps, then push them onto the screws that protrude. Once the screws are in place, sand any rough edges of the cut and then seal any gaps to ensure that there are no draughts coming into your home.

Place the Flap

If you have a basic cat flap you can leave it open and encourage your pet to use it by putting a little bit of cat food in the front of the door. Alternatively you can try pushing the cat through using your hands or a stick. Once your pet has become accustomed to walking through the flap it will be able to come and go whenever it wants. This will allow you to let it in and out as it's wanted.

It is possible to install an animal flap into the UPVC doors or glass door, but it might not be as easy as installing one inside a wooden exterior door. This is due to the fact that the UPVC doors and certain types of glass doors do not have a uniform thickness. This could have an enormous impact on the way you cut out the flap's hole and whether the flap fits correctly after installation.

The mounting kit could contain a template that outlines where to drill holes. If the kit does not include an example you can use a photocopier to make your own. It is important not to use the jigsaw to in order to cut, so it doesn't leave a bigger than necessary hole in your door.

Some cat flaps come in circular designs, which are more difficult to put in. If you have a circular flap it's important to make sure the hole is in the correct position on your door because if it's not, the cat will not be able to use the flap and may be stuck outside all day (or even at night).

Certain cat flaps come with locks that allow you to determine when your cat can enter and leave. These are very helpful in the event that you are worried about your cat going out at night and coming back in due to the darkness, or you're at work all day. The lock can be used for entry or exit and some locks can be locked in either direction which allows you to close the door completely, which is especially helpful for older or ill cats who aren't keen on going out in bad weather.